|
Also Referred to as: Load Transducer, Load Sensor, Force Sensor
The Load Cell Info page is a comprehensive section listing all of our information on load cells for those who are interested in researching the topic. If you’re searching for a specific product, we highly recommend you use our search filter on our Load Cells Page.
Selecting a sensor is a difficult task since no 1 sensor fits all applications. There is no real industry standard on how you go about selecting your product. Other challenges you may come across include finding compatible instrumentation, requiring a non-standard product that could increase delivery time and even after you pick the right sensor, if it gets installed incorrectly, there will be no good results. Additionally, it is important to find a sensor provider that has the experience to support your needs before and after the sale.
In order to keep these challenges to a minimal, there are some key things to consider during your selection process. Understanding your application and defining your requirements are a pivotal part of this procedure. After you’ve clearly defined your application, define what it is you want to measure. Do you want to measure load? This means that you want to convert input mechanical force into an electrical output signal. Note load cells are different then pressures sensors. Load cells can be used to measure surface pressure. However you would use a pressure sensor if you need to measure fluid or gas pressure. Load Cell Applications include press to viscosity / liquid separation, automation, medical bag weighing, and many more. Here are a few load cell applications that may help guide you in your selection.
Then take a look at some of the key characteristics that would define your needs. Do you have static load or is it a dynamic type? Define the mounting type. How will you be mounting this load cell? (Female / male thread, In-line, Side Mount, Flange Mount, Thru-hole, Compression Washer.) What is your load direction? (Tension, Compression, or both.)
Determining your capacity requirements are just as important as the aforementioned characteristics. Define your minimum and maximum capacity requirements. Be sure to select the capacity over the maximum operating load and determine all extraneous load & moments prior to selecting the capacity. Note: extraneous load and moments increase combined stress which would accelerate the fatigue and could also affect the performance & accuracy if the correct load cell is not selected. Most in-line sensors such as the S-Beam are not designed with extraneous load and moment capability. For endurance or fatigue applications try to operate at 50% or lower of the rated capacity.
Also be sure to define your size requirements (width, height, length, etc) and specification requirements (output, nonlinearity, hysteresis, creep, bridge resistance, etc.) Other characteristics to consider include submersible option, cryogenic option, multiple bridges, TEDS IEEE1451.4.
If you need an instrument for your application, select the instrument the same time you select the load cell. This will help you avoid any chances of non-compatibility. Don’t forget to purchase system calibration with your order. This integrates your sensor and instrument as one system.
For more tips on selecting the appropriate sensor, click here. Remember, these tips are guidelines to help point you in the right direction when selecting your sensor. It is very important to find a sensor provider that has the experience to support your needs. Find out if the company has worked with similar applications in the past. If it is a completely new application in which there is no precedence, select a company that is known for taking on these new challenges and would be able to work with you every step of the way from design to manufacturing and implementation. If you require a nonstandard product, note that your expected delivery time will increase by at least one month.
For a quick reference on how to Select Load Cells Click Here.
Load Cell Types
Load Cells manufactured in US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Load Cells, utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
A Load Cell is defined as a transducer that converts an input mechanical force into an electrical output signal. Load Cells are also commonly known as Load Transducers or Load Sensors.
Metal foil strain gauge based technology facilitates a design of a Load Cell through the following ‘Lehman’ described process (by department):
- A Load Cell ‘flexure,’ a physical unit comprised of high strength materials, is designed and fabricated by Futek Advanced Sensor Technologies Engineering Team and In-House Machine shop, respectively.
- Metal foil strain gauges are then bonded to a diaphragm or most sensitive area of physical design by Futek Advanced Sensor Technology’s Lamination Department.
- The Metal foil strain gauge Wheatstone bridge configuration is then wired by our specialized department while accounting for temperature compensation affects of the transducer/sensor.
- When Our NIST Traceable Calibration Department applies a mechanical load, a weight of tension or compression direction, the strain gauge then does its magic by capitalizing in this mechanical deformation and thus producing an electrical resistance change proportional to the load.
Futek Advanced Sensor Technologies strain gauge based Load Cells are widely known in many industries to contain:
- The Highest accuracy which may conform to many standards from the Automotive to Aerospace.
- Robust Construction made of either high strength Stainless steel or Aluminum.
- A guarantee to perform at longest possible work life even at the most rigorous conditions
- A plethora of mounting options for ANY scale ANY-where.
- Competitive pricing that separates Futek Advanced Sensor Technology from the rest.
- A full gamut of selections with capacities ranging from 10 grams to 1 MILLION pounds.
From submersible to space, Futek Advanced Sensor Technology Load Cells cover an array of applications in many industries ranging from Medical, Automotive, Aviation, Aerospace, Computer, Textile, Material Testing, Process Control, and Robotic & Automation just to name a few.
Futek Advanced Sensor Technology’s industry listing is as broad as its Sensor selection. Our selection of Load Cells can be categorized by the following styles:
- Automotive Load Cell (i.e. auto test measure devices: pedal, shifting, multi axial)
- Bending Beam Load Cell (measures force, pressure, and displacement)
- Column/Canister Load Cell (conventional and miniature column designs for compression measurement)
- Donut Load Cell (Tension or compression, designed for space limited clamp force measurement)
- Fold Back Beam Load Cell (Compact precision bending beams designed for OEM applications)
- Force Sensor (Economical OEM bending beam designed for force, pressure, and displacement)
- Load/Force Washer Load Cell (Compact hollow design for fastener clamp force measurement).
- Load Button (compression only designed for space limited applications)
- Medical Related Load Cells (Rehab force measurements, OEM bending beams, multi axis sensors)
- Overload Protection (designed to help protect sensors from accidental and or excess forces)
- Pancake Load Cells (Low profile, high precision, tension or compression Load Cell)
- S Beam/ Z beam Load Cells (Inline Load Cell, primarily for tension measurement)
- Thread female mount Load Cells (various tension or compression internal thread mount Load Cell)
- Thread male mount Load Cells (various tension or compression stud mount threaded Load Cell)
- Thru hole Load Cells (Tension or compression, designed for space limiting clamp force measurement)
Selecting the proper load cell type for your application is a critical task as each
load cell offers its own unique attributes. The following page will help
clarify the different types of load cells available to you on our site and essentially
guide you towards selecting the right load cell type.
For over a decade, FUTEK Advanced Sensor Technology has been supporting the Automotive Industries’ Load Cell requirements in endurance testing, validation, verification and qualification.
Our Automotive Load Cells are designed to fit a wide range of applications from component testing to full assembly.
Specialty products such as our Low Profile Spike Resistant Pedal Force Sensor, Bi-Axial Stick Shift Sensor, and Compact Seat Belt Sensor are selected and fully trusted
product throughout the Automotive Industry. As with any FUTEK product, any of our Automotive Load Cells can be easily modified or customized to meet your requirements.
The standard models are often available in our stock making it available quick delivery. All Load cells and Force Transducers are manufactured in the US. All Sensors are
available with in-line signal conditioned amplifier and or TEDS / IEEE1451.4 option. Available Features and Options:
- Measurements in Load and Force
- High Capacity
- Low Capacity
- Custom Strain Relief
- One piece construction suitable for endurance testing
- Low Profile Height
- Light Weight
- Available in Tension, Compression, and Multi-Component Loads
- Removable Mounting Plate
- Spike Resistant
- Excellent Off Center Loading
- Operating Temperature of -60° F - 200° F
- Capacity ranging from 10 lb to 100,000 lbs
- Utilizes Metal Foil Strain Gauge Technology
Types of Automotive Load Cells
FUTEK’s Bending Beam Load Cell category offer slim designs with an excellent endurance making them ideal for OEM applications. One clear advantage is the models
miniature size. Overload Protection is also available on select models.
The standard Bending Beam Load Cell can be modified or customized to meet your requirements and most models are available in our inventory making it available for quick delivery. Similar to our entire Load Cell product line this model is manufactured in US and uses metal foil strain gauge technology. Available Features and Options:
- Ideal for OEM Applications
- In both Tension & Compression
- Single Point Construction
- Low Capacity
- Built in Overload Protection (select models)
- Strain Gauge Based
Types of Bending Beam Load Cells
FUTEK provides a wide range of Canister Load Cells designed for high capacity compression applications. These models offer robust construction with a capacity range beginning
at 2,000 lbs going up to 1 million lbs. FUTEK has also developed a miniature Canister Load Cell series for applications where size is a critical factor. Canister Load Cells are also commonly known as Load Column Load Cells.
An additional design feature is the Canister Load Cell’s raised Spherical surface to lower the possibility of off center loading. This model can be modified or customized to meet your requirements and most models are available in our inventory making it available for quick delivery. Similar to our entire Load Cell product line this model is manufactured in US and uses metal foil strain gauge technology. Available Features and Options:
- Canister Load Cell Design
- High Capacity
- Low Capacity
- Compression
- Light Weight
- Miniature/Compact Size
- Strain Gauge Based
- TEDS / IEEE1451.4 option available for select models
Types of Canister Load Cells
In-Line Load Cell
FUTEK provides a wide range of In-line Load Cells built for Endurance, Off-Center Loading, Press, or Inline applications. These models offer robust construction with a capacity range beginning at 25 lbs going up to 50,000 lbs. FUTEK has also developed a miniature series for applications where size and tight environments are critical.
The In-Line Load Cell series also offer high accuracy and high stiffness. Anyone of these In-Line Load Cells can be modified or customized to meet your requirements and most models are available in our inventory making it available for 24 hour shipping. Similar to our entire Load Cell product line this model is manufactured in USA and uses metal foil strain gauge technology. Available Features and Options:
- Weight: 0.6 oz to 3.1 lbs
- Metric Threads available on select models
- Resistance to High Extraneous Loads
- Low Deflection
- 17-4 Steel Construction
- Both Tension & Compression
- Utilizes Metal Foil Strain Gauge Technology
Types of In-Line Load Cells
Load button load cells are designed for compression and known for their small package size. They are used in tight and limited spaces.
General purpose ones are normally designed with diaphragm construction but some higher precision ones are designed with bending beams for
low capacity and shear or column design for higher capacity. For best performance the load should be applied without the presence of any
side load or torque. Mounting could be a challenge with standard load button load cells. To overcome this challenge, some models are
available with mounting provision on the base. The ones without mounting provisions are normally retained by an outside wall or sandwiched
between the assemblies. Some versions are also available with a threaded stud in the center for probe style loading. Load button load cells
are available in various capacities ranging from 1lb to 100,000 lbs and in packages ranging from ¼” (6mm) to 3” (76mm) OD. Load button load
cells are widely used in Medical applications as well as automation where small size is a must and space is limited. If space is not an
issue and higher precision is required then use a pancake style load cell.
Load Pin Load Cell
FUTEK provides a wide range of Load/Force Washer Load Cells built Off-Center Loading, Press, or Inline compression applications. These models offer robust construction, bolt size options of #10 to 2 inches, and a capacity range beginning at 3,000 lbs going up to 300,000 lbs.
The Load/Force Washer Load Cell series also offer high accuracy and high stiffness. Anyone of these Load/Force Washer Load Cells can be modified or customized to meet your requirements and most models are available in our inventory making it available for 24 hour shipping. Similar to our entire Load Cell product line this model is manufactured in USA and uses metal foil strain gauge technology. Available Features and Options:
- Standard cable includes 10 feet 4 Conductor shielded cable
- Position Sensitive
- Low Deflection
- 17-4 Steel Construction
- Both Tension & Compression
- Utilizes Metal Foil Strain Gauge Technology
Types of Load/Force Washer Load Cells
The Low Profile Load Cell Series offers 4 models for S-Beam type in-line loading applications. You will find a capacity range of 10 lbs to 1000 lbs, and flexure options of 2024 Aluminum or 17-4 Stainless Steel. The LRF series features a compact design with accurate measurements in both Tension and compression and it is available with in-line signal conditioned amplifier and/or TEDS / IEEE1451.4 option.
Our standard load cells can be easily modified or customized to meet your requirements and most models are available in our inventory making it available for 24 hour shipping. Similar to our entire Load Cell product line this model is manufactured in the US and uses metal foil strain gauge technology. Available Features and Options:
- Light Weight
- Low Deflection
- Available in both Aluminum and Stainless Steel
- In both Tension & Compression
- Operating Temperature of -60° F - 200° F
- Capacity ranging from 10 lbs to 1000 lbs
- Utilizes Metal Foil Strain Gauge Technology
- Cable & Strain Relief Option
Types of Rectangular Female / Female Thread Load Cells
Since its inception, FUTEK has provided medical Load Cell solutions for numerous medical related applications. In most cases, we are able to modify our existing load cells.
Listed below is a brief listing of a select sample of medical Load Cells applications we have experience working with. For a full list please contact us. Knowing the sensitivity and difficult requirements often demanded in medical related applications, FUTEK has taken the proactive step to bring a medical practitioner to its consulting staff to ensure we can support you with your challenging applications. We highly recommend our customers to contact us as we have found that these applications require a great degree of experience and expertise.
Available Features and Options:
- Drug delivery control systems (automated)
- Fitness Equipment/ Rehab Equipment
- Fluid Weighing
- Infusion Pump Control
- Medical bag weighing applications
- Research Testing
- Sanitary applications (differential pressure measurements)
- Seal Testing
- Sterilization/Packaging Systems
Types of Medical Load Cells
Pancake Load Cells, also known as low profile Load Cells,
are commonly used in applications that require high precision, and less sensitive
to load condition. For most capacities the Pancake Load Cell is normally designed with
multiple shear struts. For lower capacities it’s designed with bending beams. If properly
designed and manufactured, the nature of its structure is less sensitive to extraneous load
and moments (especially Torque) compared to other inline sensors such as the S Beam Load
Cell, diaphragm or column type. This type of Load Cell is normally used in press in
compression for controlling the applied load or pressure during the test or production.
Pancake Load Cells normally provide a female thread thru the center and multiple thru
holes on outer ring for mounting. Fixing the outside mounting holes will allow for it
to be used in tension as well. Also by adding the tension base plate option users can
utilize it in-line in both tension and compression, just like the S Beam Load Cell.
Capacities ranges vary depending on the manufacturer, but Pancake Load Cells are generally
offered from 50 lbs to 1 million lbs. Standard features typically include metric thread
and quick disconnect. Fatigue rated Pancake Load Cells are also available and widely used
in endurance testing applications. Submersible versions are also available with integrated
cables. Some manufacturers also offer built-in amplifiers with VDC/4-20mA or with
TEDS per IEEE1451.4 option for plug & play.
Types of Pancake Load Cells
Rod End Load Cell
FUTEK’s Rod End Load Cells provide an excellent solution for applications involving Inline Actuators or Hydraulic Jacks with Male/Female Threads. You will find a capacity
range of 100 lbs to 20,000 lbs, and flexure options of 2024 Aluminum or 17-4 Stainless Steel.
The Rod End Load Cell series maintain high accuracy and high stiffness. The standard Load Cell can be modified or customized to meet your requirements and most models are available in our inventory making it available for quick delivery. Similar to our entire Load Cell product line this model is manufactured in US and uses metal foil strain gauge technology. Available Features and Options:
- Weight: approximately 3.5 oz – 1 lb
- External matched output option available
- Fatigue Rating Available
- Low Capacity / High Capacity
- Low Deflection
- 17-4 Steel Construction
- In both Tension & Compression
- Utilizes Metal Foil Strain Gauge Technology
Types of Rod End Load Cells
The S Beam Load Cell, also known as the Z Beam Load Cell, is one of the most popular types of load cells.
It was originally designed for inline applications to convert mechanical scale to digital by replacing the spring
or other in-line hardware. The S Beam Load Cell is available in variety of load ranges with both English & Metric
threads. It is very popular due to its high precision, low price, and ease of installation. But since S Beam Load
Cells are strictly designed for in-line applications they are very sensitive to extraneous load, torque, and moments.
Off center loading must be avoided for the best performance & longer service life. Please refer to the pancake type
load cell for applications requiring off center loading or extraneous load, moment and torque capabilities.
Typical
features of the S Beam Load Cell include an integrated cable or quick disconnect receptacle. S Beam Load Cells also
come in full hermetic sealed versions and submersible types. In recent years, miniature versions of the S Beam Load
Cell known as S Beam Load Cell Junior has also been designed and manufactured. The S Beam Load Cell Jr.
(Miniature S Beam Load Cell) comes with effective built-in mechanical stop for overload protection in both Tension
and Compression and is available from 10 grams full scale to 100 lbs. This innovative model comes in package sizes
smaller than a quarter coin and is widely used in bag hanging medical applications during the dialysis process, as
well as other automated applications in which small package size is essential.
Single Point Load Cell - (Also known as Side Mount Load Cells, Parallelogram Sensors or Belt Buckle Sensors)
Single Point Load Cells are usually designed for processing applications which require weight control platforms, usually on the small scale type. They are given their name because they can be used for these platform applications supporting off center loading by utilizing only one sensor. The advantage of this particular load cell design over others is that it is low profile, has high precision, and can be adjusted for off center loading. This particular load cell type is generally easy to mount. Other products for similar applications such as load buttons are not as easy to mount. This load cell is also designed for high volume OEM applications and offered in a wide range of capacities from Gram ranges to 500 lbs in the same form fit function.
FUTEK’s particular line of Single Point Load Cells is more compact compared to the same product by other manufacturers. It averages in dimension about 2 x 0.5 x 2 inches compared to 4x1x3 inches. It also offers overload protection making it suitable for both process control and material testing applications since possible overload usually occurs during installation. Due to its size and precision it has widely been used in Handheld or portable equipment as well as many material testing machines. Other popular applications are in-line food processing or material process control or batching systems.
Also due to its compact size, high precision and long Mean Time Between Failure (MTBF of very well over 100 million cycles) it has been an ideal choice for many medical applications such as automated blood management system, dialysis and bag hanging applications for drug delivery application.
Threaded Miniature S Beam Load Cell
FThe Thru Hole Donut Load Cell Series offers 5 models built for Off-Center Loading, Press, or Inline compression applications. These models have a very robust construction available in 17-4 Stainless Steel, with an I.D. range of 1/8" to 1 1/4".
The Donut/Thru Hole Load Cell also offer high accuracy and high stiffness. The standard models can be modified or customized to meet your requirements and most models are available in our inventory making it available for 24 hour shipping. Similar to our entire Load Cell product line this model is manufactured in USA and uses metal foil strain gauge technology. Available Features and Options:
- Weight: 2 oz to 85 lbs
- Resistance to High Extraneous Loads
- Low Deflection
- 17-4 Steel Construction
- Compression
- Utilizes Metal Foil Strain Gauge Technology
- High Accuracy
Types of Thru Hole Donut Load Cells
Weld Probe Load Cell
| Available Models |
LAU200 (L1050)
Pedal Force Sensor
 |
Pedal Force Load Cell The LAU200 Pedal Force Load Cell offers an ideal solution for Automotive Applications. From its 17-4PH Stainless Steel one piece construction, to its low profile design (Off-center loading error of <4%), the LAU200 Pedal Force Load Cell offers a great measurement system with impressive tolerances. This unit comes with a removable mounting plate and it includes a Lemo mating connector with PVC cable. The LAU200 Pedal Force Load Cell is manufactured in US, and similar to our entire Load Cell product line, uses metal foil strain gauge technology.
Product Highlights:
- Ideal for Automotive Applications
- One Piece Construction
- Strain Gauge Based
- Low Profile Height
- Removable Mounting Plate
|
|
LAU220 (L1055)
Pedal Force Sensor
|
Pedal Force Load Cell The LAU220 Pedal Force Load Cell has become one of the most common and trusted products in the Automotive Industry. From its 17-4PH Stainless Steel one piece construction, to its low profile design (Off-center loading error of <1%), the LAU220 Pedal Force Load Cell offers a great measurement system with impressive tolerances. This unit comes with a removable mounting plate, custom built strain relief, spike resistant, and a machined slip-resistant top surface. The LAU220 Pedal Force Load Cell is manufactured in US, and similar to our entire Load Cell product line, uses metal foil strain gauge technology.
Product Highlights:
- Ideal for Automotive Applications
- One Piece Construction
- Strain Gauge Based
- Low Profile Height
- Removable Mounting Plate
- light weight
|
|
LAU300
Seat Belt Sensor
|
Automotive Transducer - Seat Belt The LAU300 Automotive Transducer - Seat Belt is yet another unique product offered for the Automotive Industry. Designed to test the tension forces on seat belt the LAU300 Automotive Transducer - Seat Belt is made from Anodized Aluminum, making it extremely light weight, and offers a compact design that is easy to use. Additional design features include the use of a strain relief providing the cable much greater protection The LAU330 Automotive Transducer - Seat Belt is manufactured in US, and similar to our entire Load Cell product line, uses metal foil strain gauge technology.
Product Highlights:
- Ideal for Automotive Applications
- Accepts belts up to 0.1” thick
- Strain Gauge Based
- Compact design
- Light Weight
- Custom Strain Relief
|
|
LBB200 (L1501)
Bending Beam
|
Bending Beam Load Cell The LBB200 Bending Beam Load Cell offers a slim design making it ideal for OEM applications. Utilized in Compression, the Bending Beam Load Cell can be used to measure force, pressure and displacement for OEM Applications. With its miniature size, the Bending Beam Load Cell is a great selection for any tight environments. The LBB200 Bending Beam Load Cell is offered in Stainless Steel and has a shielded PVC cable.
As a part of FUTEK’s original product line, the Bending Beam Load Cell can be modified or customized to meet your requirements. The standard models are in our stock making them available for 24 hour shipping. Similar to our entire Load Cell product line, this model is manufactured in US, and uses metal foil strain gauge technology.
Product Highlights:
- Ideal for OEM Applications
- Compression
- Can be utilized to measure force, pressure, and displacement for OEM Application
- Strain Gauge Based
- Exposed elements
- Light Weight
|
|
LBB300 (L1510)
Bending Beam w/ Overload Protection
|
Bending Beam Load Cell The LBB300 Bending Beam Load Cell offers a unique solution for smart switches. As a recent custom engineered product, the Bending Beam Load Cell captures the many capabilities FUTEK offers its customers. This product can be used to measure force, pressure, and displacement. With its miniature size, the Bending Beam Load Cell is a great selection for any tight environments.
The standard models are in our stock making them available for 24 hour shipping. Similar to our entire Load Cell product line, this model is manufactured in US, and uses metal foil strain gauge technology.
Product Highlights:
- Ideal for Smart Switch Applications
- Compression
- Strain Gauge Based
- Light Weight
- Wide Capacity Range
|
|
LCA300 (L1645)
Miniature Load Column Load Cell
|
Column Load Cell (Miniature) FUTEK’s Column Load Cell (Miniature) offers an impressive compact design for high capacity applications. With a diameter of 0.62”, it is ideal for tight spaces. The LCA300 Column Load Cell (Miniature) is offered in 17-4PH Stainless Steel in 2,000 lbs to 5,000 lbs, with a raised surface radius to lower the possibility of off center loading.
The Column Load Cell (Miniature) is designed to measure loads in compression. This model is manufactured in US, and similar to our entire Load Cell product line, uses metal foil strain gauge technology. Additional design features include the use of a strain relief providing much greater protection from the pull on the cable.
Product Highlights:
- Low Deflection
- Compression
- Small profile for tight spaces
- High Capacity Miniature Load Column/Canister Load Cell
|
|
LCA305 (L1645)
Miniature Load Column Load Cell
|
Column Load Cell (Miniature) FUTEK’s Column Load Cell (Miniature) offers an impressive compact design for high capacity applications. With a diameter of 0.88”, it is ideal for tight spaces. The LCA305 Column Load Cell (Miniature) is offered in 17-4PH Stainless Steel in 7,500 to 10,000 lbs, with a raised surface radius to lower the possibility of off center loading.
The Column Load Cell (Miniature) is designed to measure loads in compression. This model is manufactured in US, and similar to our entire Load Cell product line, uses metal foil strain gauge technology. Additional design features include the use of a strain relief providing much greater protection from the pull on the cable.
Product Highlights:
- Low Deflection
- Compression
- Small profile for tight spaces
- High Capacity Miniature Load Column/Canister Load Cell
|
|
LCA310 (L1645)
Miniature Load Column Load Cell
|
Column Load Cell (Miniature) FUTEK’s Column Load Cell (Miniature) offers an impressive compact design for high capacity applications. With a diameter of 1.25”, it is ideal for tight spaces. The LCA310 Column Load Cell (Miniature) is offered in 17-4PH Stainless Steel in 15,000 lbs to 30,000 lbs, with a raised surface radius to lower the possibility of off center loading.
The Column Load Cell (Miniature) is designed to measure loads in compression. This model is manufactured in US, and similar to our entire Load Cell product line, uses metal foil strain gauge technology. Additional design features include the use of a strain relief providing much greater protection from the pull on the cable.
Product Highlights:
- Low Deflection
- Small profile for tight spaces
- Compression
- High Capacity Miniature Load Column/Canister Load Cell
|
|
LCA345 (L1618)
Miniature Compression Load Cell
|
Compression Load Cell (Miniature) FUTEK’s Compression Load Cell (Miniature) offers an impressive compact design for high capacity applications. With a diameter of 0.63", it is ideal for tight spaces. The LCA345 Compression Load Cell (Miniature) is offered in 17-4PH Stainless Steel in 4,000 lbs & 5,000 lbs, with a raised surface radius to lower the possibility of off center loading.
The Compression Load Cell (Miniature) is designed to measure loads in compression. This model is manufactured in US, and similar to our entire Load Cell product line, uses metal foil strain gauge technology. Additional design features include the use of a strain relief providing much greater protection from the pull on the cable.
Product Highlights:
- Compact Height
- High Capacity
- Low Deflection
- High Frequency Response
- Spherical Radius Load Surface
|
|
LCA350 (L1618)
Miniature Compression Load Cell
|
Compression Load Cell (Miniature) FUTEK’s Compression Load Cell (Miniature) offers an impressive compact design for high capacity applications. With a diameter of 0.88", it is ideal for tight spaces. The LCA350 Compression Load Cell (Miniature) is offered in 17-4PH Stainless Steel in 7,500 lbs & 10,000 lbs, with a raised surface radius to lower the possibility of off center loading.
The Compression Load Cell (Miniature) is designed to measure loads in compression. This model is manufactured in US, and similar to our entire Load Cell product line, uses metal foil strain gauge technology. Additional design features include the use of a strain relief providing much greater protection from the pull on the cable.
Product Highlights:
- Compact Height
- High Capacity
- Low Deflection
- High Frequency Response
- Spherical Radius Load Surface
|
|
LCA700
High Capacity Load Cell (Column/Canister)
|
High Capacity Load Cell (Column/Canister) FUTEK’s LCA700 High Capacity Load Cell (Column/Canister) offers a compact design for high capacity compression applications. The LCA700 High Capacity Load Cell (Column/Canister) is offered in 17-4PH Stainless Steel in 500,000 lbs to 1 million lbs, has a raised Spherical surface to lower the possibility of off center loading, and comes equipped with a handle for easy carrying.
FUTEK’s Canister (LCA) Series are manufactured in US, and similar to our entire Load Cell product line, use metal foil strain gauge technology. For a lower capacity of this style please refer to LCA300 series.
Product Highlights;
- Canister/Column Load Cell Design
- High Capacity – Small Package Size, light weight
- Strain Gauge Based
- Handle for easy carrying
- Connector
|
|
LCB200 (L1652)
Tension & Compression Load Cell
|
Rod End Load Cell (Tension/Compression) Model LCB200 is a Rod End Load Cell (Tension/Compression) designed for applications involving Inline Actuators or Hydraulic Jacks with Male/Female Threads. The standard LCB200 Rod End Load Cell (Tension/Compression) model has male/female threads, built from robust 17-4PH Stainless Steel, and weighs approximately 3.5 oz. This model is well suited for the mid range capacity requirements (1,000 lb – 3,000 lb) offering high endurance and excellent accuracy. For any applications that require a higher capacity range, please refer to the LCB400, LCB450 and LCB500
This Rod End Load Cell (Tension/Compression) has high accuracy and high stiffness. It has Nonlinearity of ±0.5%, Bridge Resistance of 1000 ohms, and Deflection of 0.001” nominal. The standard LCB200 Rod End Load Cell (Tension/Compression) can be modified or customized to meet your requirements, and most capacities are in our inventory, making them available for 24 hour shipping. Similar to our entire Load Cell product line this model is manufactured in US, and uses metal foil strain gauge technology.
Product Highlights:
- Light Weight
- External matched output option available
- Fatigue Rating Available
- Teflon Cable Option
- Female/Male Threads
- Low Deflection
- 17-4 Stainless Steel Construction
- In both Tension & Compression
- Mid Range Capacity Applications
- Utilizes Metal Foil Strain Gauge Technology
|
|
LCB400 (L1658)
Tension & Compression Load Cell
|
Rod End Load Cell (Tension/Compression) Model LCB400 is a Rod End Load Cell (Tension/Compression) designed for applications involving Inline Actuators or Hydraulic Jacks with Male/Female Threads. The standard LCB400 Rod End Load Cell (Tension/Compression) model has male/female threads, uses a lightweight 2024 Aluminum for lower capacities and a robust 17-4 Stainless Steel for the higher capacities. This model is well suited for the mid range to high range capacity requirements (1,000 lb – 10,000 lb). For any applications that require a higher capacity range, please refer to the LCB450.
This Rod End Load Cell (Tension/Compression) has high accuracy and high stiffness. It has Nonlinearity of ±0.5% and Deflection of 0.001” nominal. The standard LCB400 Rod End Load Cell (Tension/Compression) can be modified or customized to meet your requirements and most models are in our inventory, making them available for 24 hour shipping. Similar to our entire Load Cell product line, this model is manufactured in US, and uses metal foil strain gauge technology.
Product Highlights:
- Weight: 8 oz - 20 oz
- Low Deflection
- Bendix Receptacle
- Optional Mating Connector
- 2024 Aluminum or 17-4 Stainless Steel Construction
- In both Tension & Compression
- Mid Range to High Range Capacity Applications
- Utilizes Metal Foil Strain Gauge Technology
|
|
LCB450 (L1659)
High Capacity Load Cell (Rod End/Fatigue Rated)
|
High Capacity Load Cell (Rod End) Model LCB450 is a High Capacity Load Cell (Rod End) for Inline Actuators or Hydraulic Jacks with Male/Female Threads. The standard LCB450 High Capacity Load Cell (Rod End) model has male/female threads and Bendix Receptacle. It uses 17-4 Stainless Steel and weighs approximately 20 oz. This model is well suited for the mid range to high range capacity requirements (5,000 lb – 20,000 lb). For any applications that require a lower capacity range, please refer to the LCB200 and LCB400.
This High Capacity Load Cell (Rod End) has high accuracy and high stiffness. It has Nonlinearity of ±0.5%, and Deflection of 0.001” nominal. The standard LCB450 High Capacity Load Cell (Rod End) can be modified or customized to meet your requirements and most models are in our inventory, making them available for 24 hour shipping. Similar to our entire Load Cell product line, this model is manufactured in US, and uses metal foil strain gauge technology.
Product Highlights:
- Light Weight
- Low Deflection
- Fatigue Rated
- 17-4 Stainless Steel construction
- Bendix Receptacle
- Optional Mating Connector
- In both Tension & Compression
- High Capacity Applications
- Utilizes Metal Foil Strain Gauge Technology
|
|
LCB500 (L2930)
Tension & Compression Load Cell w/ Male Center Stud
|
Tension and Compression Load Cell Model LCB500 is a Tension and Compression Load Cell (can be used as Rod End with mounting plates) for Inline Actuators or Hydraulic Jacks with Male/Female Threads. The standard LCB500 Tension and Compression Load Cell model has male/female threads, is a welded unit and comes with a Bendix Receptacle. The Flexure is made from Stainless Steel making it highly durable and ideal for endurance testing. This model is well suited for both low range to high range capacity applications (100 lb – 5,000 lb).
This Tension and Compression Load Cell has high accuracy, excellent resistance to high extraneous loads, and high stiffness. It has Nonlinearity of ±0.25%, and Deflection of 0.002 to 0.005” nominal. The standard LCB500 Tension and Compression Load Cell can be modified or customized to meet your requirements and most models are in our inventory, making them available for 24 hour shipping. Similar to our entire Load Cell product line, this model is manufactured in US, and uses metal foil strain gauge technology.
Product Highlights:
- Light Weight (1 lb)
- One piece construction
- Bendix Receptacle
- Optional Mating Connector
- Low Deflection
- Stainless Steel
- In both Tension & Compression
- Low Range to High Capacity applications
- Utilizes Metal Foil Strain Gauge Technology
|
|
LCF250 (Q10476)
Tension and Compression Load Cell
|
Tension and Compression Load Cell Model LCF250 is a Tension and Compression Load Cell designed for Inline applications. The flexure is built from a robust 17-4PH Stainless Steel, 3/8-24 threads, and weighs approximately 3 oz. With its miniature design, the LCF250 Tension and Compression Load Cell is an excellent solution for applications where vertical space is limited. Additional design features include the use of a strain relief providing much greater protection from the pull on the cable.
This Tension and Compression Load Cell has high accuracy and high stiffness. It has Nonlinearity of ±0.5% and Deflection of 0.001” nominal. The standard LCF250 Tension and Compression Load Cell can be modified or customized to meet your requirements, and most models are in our inv | | |